| HOME > PRODUCTS > FULLY AUTOMATIC TUNGSTEN CARBIDE SAWING MACHINE |
 |
| |
 |
 |
- Servo-motor drive + ball screw feed transmission
- Hydraulic driven sawhead feed for Cutting motion
- THC-B165NC Sawhead driven by servo-motor + Ball screw transmission for cutting. (optional)
- Feeding safety guard (optional)
- Fully feeding safety guard (optional)
|
| |
|
|
| |
|
 |
| |
- The THC-70NC．THC-130NC．THC-165NC．High Speed Tungsten Carbide Sawing Machine is designed and engineered to create optimum cutting performance. It features high speed, high efficiency, smooth surface of cut and high accuracy.
The THC-70NC．THC-130NC．THC-165NC is especially ideal for cutting solid bars and angular steel. Also suitable for cutting steel pipe by using a HSS sawblade.
- THC-A Hydraulic driven sawhead feed for cutting motion(standard).
THC-B Sawhead driven by servo-motor + Ball screw transmission for cutting (optional)
|
 |
| |
|
| |
| CUTTING
CAPACITY |
TCT CARBIDE SAWBLADE |
| Round solid
bar |
mm |
●70 ~ 165 |
| Square solid
bar |
mm |
■70 ~130 |
| Rectangle |
mm |
▃▃80~120 |
| Square pipe |
mm |
-- |
| Square pipe |
mm |
-- |
| Maximum
length of
head cut |
mm |
10
~ 50 |
| Waste
material
length at
tail end |
mm |
85~(85 + π
Cutting length) |
| Feeding
length |
mm |
5 ~ 640 Continuous cycles |
| Manually
stack
line-up
loader
capacity |
kg |
4600 |
| Material
length |
mm |
3000
~ 6000 |
| Material
loading
width |
mm |
900 |
| MACHINE
SPECIFICATIONS |
| TCT CARBIDE SAWBLADE |
mm |
460 x 2.3 x t 2.7 std.
480 x 2.3 x t 2.7 opt. |
| Pin holes + Bore |
mm |
4 x 21 x PCD 90 x Ø50 |
| Tip aluminum carbide sawblade |
mm |
-- |
| Pin holes + Bore |
mm |
-- |
| Hss sawblade |
mm |
-- |
| Spindle motor |
kw |
11kw x 6P (15HP x 6P) |
| Spindle speeds |
rpm |
30 ~ 90 rpm. |
| Frequency Inverter |
|
15 kw (20HP) |
| Hydraulic pump motor |
kw |
3.7 kw x 4P (5HP x 4P) |
| Operation pressure |
|
7 mpa 70 kg/cm2 |
| Oil tank capacity |
ℓ |
約150 |
| Air pressure |
mpa |
0.4 ~ 0.6 mpa 4 ~ 6 kg/cm2 |
| Feed drive |
|
AC servo-motor (1.8kw or 2.0 kw) and precision ball screw |
| Sawhead drive |
|
A.Material feeding and cutting is driven by hydraulic system.
B.AC servo-motor + ball screw transmission for cutting (optional) |
| Feeding vise |
|
Horizontal hydraulic type |
| Main vise |
|
Horizontal and vertical hydraulic type, one set each |
| MACHINE DIMENSIONS AND WEIGHT |
|
|
| Machine size |
mm |
6700 x 2200 x 1900 |
| Weight
(Machine + Feeder) |
kg |
4000+1600 |
*
The manufacturer
always performs
product
improvements to
achieve the best
possible
performance.
All specifications, dimensions and design characteristics shownin
this catalogue
are subject to
change
without notice. Product specifications are based on the actual
machines. The
manufacturer
holds
explanation rights. |
|
|
|
- Sawblade
gap
compensation
device
- Tungsten pad
for sawblade
run-out
- Chip
removing steel
brush wheel
- Screw type
chip conveyor
- Mist cooling
device
- Cutting
fluid cooling
device
- Work light
|
|
|
|
| |
-
TCT sawblade
-
Mist collecting device
-
Cutting fluid
-
Angular steel sliding device
|
|
|
|
|
|
|
|
